Washing machine error codes and fault guides
Browse 130 published, evidence-gated Washing machine guides. Each page states the supported model and region, official source, safe checks, and the point to stop.
Washing machine fault guides
25–48 of 130
a washing-machine control condition
E41 / F41 is identified by Bosch support as a washing-machine control condition. Follow the official, model-scoped checks and service boundary below.
a washing-machine motor-speed condition
E42 / F42 is identified by Bosch support as a washing-machine motor-speed condition. Follow the official, model-scoped checks and service boundary below.
Washer control thinks the door switch is open
E41 is described by Electrolux support as washer control thinks the door switch is open. Exact checks and component access vary by model and region.
incorrect washing-machine settings
E00 is identified by Gorenje support as incorrect washing-machine settings. Follow the official, model-scoped checks and service boundary below.
a washing-machine temperature-sensor error
E01 is identified by Gorenje support as a washing-machine temperature-sensor error. Follow the official, model-scoped checks and service boundary below.
a washing-machine water-heating error
E06 is identified by Gorenje support as a washing-machine water-heating error. Follow the official, model-scoped checks and service boundary below.
The washing machine has detected a water-level sensor problem
Gorenje identifies E10 as a water-level-sensor error. The published first check is a safe isolation, drain, and accessible filter or trap inspection.
The washing machine has detected too much water
Gorenje uses E11 for a water-overflow condition. If the appliance continues filling, close the water tap immediately and use qualified service.
The washing-machine rotor is blocked
Gorenje identifies E12.5 as a blocked rotor condition. With power isolated, check whether an object or trapped laundry is mechanically blocking the drum.
The Ultra clean programme detected laundry in the drum
Gorenje uses E13.3 when a load is detected during Ultra clean. Remove every item from the drum, reconnect once, and restart the empty programme.
The washing-machine door cannot lock correctly
Gorenje identifies E22 as a door-locking error. Check that nothing obstructs the latch, then isolate and reconnect power once before service.
The washing machine is not filling with water correctly
The Gorenje washing-machine manual uses E3 for a water-filling error. Check the visible supply path and inlet filter against the manual before a single controlled test.
The washer is receiving voltage below or above the stated range
Gorenje identifies E40 as mains voltage outside the stated range. Do not test live mains yourself; use a qualified electrician or appliance service.
an incorrect washing-machine mains frequency warning
E41 is identified by Gorenje support as an incorrect washing-machine mains frequency warning. Follow the official, model-scoped checks and service boundary below.
The washing machine cannot drain water normally
Gorenje uses E7 and E7.2 for a water-draining error. The official procedure covers the pump filter, drain hose, drain, and pump impeller.
The washing machine has detected a water leak
Gorenje uses E9 when water leakage is detected. Inspect only the visible exterior and wall siphon, then stop if the leak or code returns.
The washing machine needs the published drum-cleaning maintenance cycle
Gorenje uses E92 as a drum-cleaning warning. Clean the user-accessible detergent, hose, gasket, and pump-filter areas, then run Ultra clean empty.
The washing machine cannot confirm that the door is locked
Gorenje identifies E:02 as a door-lock error in manual 904001en. Check the door closure once, then isolate power and use service if the code returns.
The washing machine is not receiving water within the expected filling conditions
Gorenje identifies E:03 as a water-filling error. Check the tap, inlet filter, hose, and published pressure range before one controlled resume.
The washing machine cannot drain water through the expected route
Gorenje identifies E:07 as a water-draining error. Inspect the pump filter, hose, drain, and hose height before one controlled resume.
The washer has detected a possible water leak in or around the appliance
Gorenje identifies E:09 as water detected in the washing-machine area. Inspect only the exterior and stop if a leak is visible.
The washer motor-control system has detected a fault or an abnormal load condition
Gorenje identifies E:12 as a motor-control error. Redistribute stuck or tangled laundry once, then use service if the code returns.
The washer cannot unlock the door after the programme or interruption
Gorenje groups E:23 and E:24 as door-unlocking errors. Turn the washer off and on once; recurring codes need service.
the Anti-crease function is active
E_AC is identified by Gorenje support as the Anti-crease function is active. Follow the official, model-scoped checks and service boundary below.