Appliance guides

Dishwasher error codes and fault guides

Browse 235 published, evidence-gated Dishwasher guides. Each page states the supported model and region, official source, safe checks, and the point to stop.

235Published guides
9Current page
10Total pages
Verified catalog

Dishwasher fault guides

193–216 of 235

MieleHigh attention
DishwasherF601

AutoDos automatic-dispensing fault

F601 is identified by Miele's official, appliance-specific source as AutoDos automatic-dispensing fault. Follow only the model-scoped checks and safety boundary below.

MieleHigh attention
DishwasherF78

circulation-pump fault

F78 is identified by Miele's official manual as circulation-pump fault. Follow the exact model-scoped checks and safety boundary below.

SamsungHigh attention
Dishwasher3E

The incoming water is too hot

Samsung identifies 3E as a high-temperature water-supply error. Verify the hot-water supply is not above 176°F before requesting service.

SamsungHigh attention
Dishwasher4C / 4E

The dishwasher is not receiving water at the required pressure or temperature

Samsung identifies 4C and 4E as water-supply errors. Check the supply shut-off, temperature, pressure, and visible hose path before service.

SamsungCheck soon
Dishwasher5C / SC / 5E / SE

The dishwasher cannot drain

Samsung identifies 5C, SC, 5E, and SE as drain errors. Check the sink connection, hose routing, filter area, and frozen drain line before service.

SamsungCheck soon
Dishwasher7E

The WaterWall reflector cannot move correctly

Samsung identifies 7E as a WaterWall reflector error. Remove obstructions, correct the reflector position, and reseat it only as the official guide shows.

SamsungHigh attention
Dishwasher9E

The dishwasher has detected too little water

Samsung identifies 9E as a low-water-level error. Empty the dishwasher, add detergent, run one Normal cycle, and request service if it returns.

SamsungHigh attention
DishwasherHC

The dishwasher temperature is too high

Samsung identifies HC as a high-temperature heater error. Follow the empty Normal-cycle check exactly once, then request service if HC returns.

SamsungHigh attention
DishwasherHE

The dishwasher is detecting temperature incorrectly

Samsung identifies HE as a heater error where temperature is detected incorrectly. Run the official empty Normal-cycle check once, then request service.

SamsungHigh attention
DishwasherOC / 0C / oE

There is more water in the dishwasher than there should be

Samsung identifies OC, 0C, and oE as over-level water errors. Use the official drain and overflow checks, then stop if water remains or the code returns.

SiemensHigh attention
DishwasherE01 / E02 / E03 / E04 / E05

Electronic fault or interrupted programme

E01 / E02 / E03 / E04 / E05 is described by Siemens support as electronic fault or interrupted programme. Exact checks and component access vary by model and region.

SiemensHigh attention
DishwasherE06

Door sensor or electronics fault

E06 is described by Siemens support as door sensor or electronics fault. Exact checks and component access vary by model and region.

SiemensCheck soon
DishwasherE08

Water level in the rinse bath is too low

E08 is described by Siemens support as water level in the rinse bath is too low. Exact checks and component access vary by model and region.

SiemensHigh attention
DishwasherE09 / E11

Internal heating-system fault

E09 / E11 is described by Siemens support as internal heating-system fault. Exact checks and component access vary by model and region.

SiemensHigh attention
DishwasherE10

The dishwasher drying system has reported a fault

Siemens identifies E10 as a fault in the dishwasher drying system and directs owners to Siemens Service for the model-specific repair.

SiemensCheck soon
DishwasherE12

The heating element is calcified or soiled

Siemens identifies E12 as a calcified or soiled heating element and recommends descaling the dishwasher according to its instructions.

SiemensUrgent
DishwasherE15 / E3100

Water detected in the base pan; leak protection active

E15 / E3100 is described by Siemens support as water detected in the base pan; leak protection active. Exact checks and component access vary by model and region.

SiemensCheck soon
DishwasherE16 / E3400

Water-fill system fault

E16 / E3400 is described by Siemens support as water-fill system fault. Exact checks and component access vary by model and region.

SiemensCheck soon
DishwasherE18 / E3200

Water inlet restricted or blocked

E18 / E3200 is described by Siemens support as water inlet restricted or blocked. Exact checks and component access vary by model and region.

WhirlpoolHigh attention
Dishwasher1 Pause 1 Pause

the dishwasher is reporting a flashing-code sequence corresponding to F1E1

1 Pause 1 Pause is identified by Whirlpool support as the dishwasher is reporting a flashing-code sequence corresponding to F1E1. Follow the official, model-scoped checks and service boundary below.

WhirlpoolHigh attention
Dishwasher10 Pause 5 Pause

the dishwasher is reporting a flashing-code sequence corresponding to F10E5

10 Pause 5 Pause is identified by Whirlpool support as the dishwasher is reporting a flashing-code sequence corresponding to F10E5. Follow the official, model-scoped checks and service boundary below.

WhirlpoolHigh attention
Dishwasher6 Pause 1 Pause

the dishwasher is reporting a flashing-code sequence corresponding to F6E1

6 Pause 1 Pause is identified by Whirlpool support as the dishwasher is reporting a flashing-code sequence corresponding to F6E1. Follow the official, model-scoped checks and service boundary below.

WhirlpoolHigh attention
Dishwasher8 Pause 1 Pause

the dishwasher is reporting a flashing-code sequence corresponding to F8E1

8 Pause 1 Pause is identified by Whirlpool support as the dishwasher is reporting a flashing-code sequence corresponding to F8E1. Follow the official, model-scoped checks and service boundary below.

WhirlpoolUrgent
Dishwasher8 Pause 4 Pause

the dishwasher is reporting a flashing-code sequence corresponding to F8E4

8 Pause 4 Pause is identified by Whirlpool support as the dishwasher is reporting a flashing-code sequence corresponding to F8E4. Follow the official, model-scoped checks and service boundary below.