Dishwasher error codes and fault guides
Browse 102 published, evidence-gated Dishwasher guides. Each page states the supported model and region, official source, safe checks, and the point to stop.
Dishwasher fault guides
25–48 of 102
a dishwasher dispenser or control condition
E19 is identified by Bosch support as a dishwasher dispenser or control condition. Follow the official, model-scoped checks and service boundary below.
a dishwasher electrical or circulation condition
E20 is identified by Bosch support as a dishwasher electrical or circulation condition. Follow the official, model-scoped checks and service boundary below.
a dishwasher circulation-pump condition
E21 is identified by Bosch support as a dishwasher circulation-pump condition. Follow the official, model-scoped checks and service boundary below.
a dishwasher filter or drainage condition
E22 is identified by Bosch support as a dishwasher filter or drainage condition. Follow the official, model-scoped checks and service boundary below.
Door is open or not successfully latched
CL / Cd is described by Electrolux support as door is open or not successfully latched. Exact checks and component access vary by model and region.
Dishwasher did not drain properly
i20 is described by Electrolux support as dishwasher did not drain properly. Exact checks and component access vary by model and region.
Clogged filter or sump
i40 is described by Electrolux support as clogged filter or sump. Exact checks and component access vary by model and region.
The dishwasher has detected too much water
Gorenje identifies F10 as a dishwasher overfilling condition. The official first check is the accessible drainage pump area; use service if F10 persists.
The dishwasher cannot discharge water correctly
Gorenje uses F11 for a water-outlet fault. Check the accessible filters, pump area, and visible drain path with power isolated before service.
The dishwasher is not receiving water correctly
Gorenje identifies F12 as a water-inlet fault. Check the tap and external inlet-hose filter only after closing water and isolating power.
The dishwasher inlet valve is leaking
Gorenje uses F40 for an inlet-valve leakage condition. Close the water tap immediately and arrange service; do not attempt a valve repair.
The dishwasher heater has reported a fault
Gorenje identifies F41 as heater fault 1. Close the water tap, unplug the dishwasher, and use qualified service for the heater diagnosis.
The dishwasher diverter has reported a fault
Gorenje uses F45 for a diverter fault. The official table does not verify a user repair, so record the model and arrange service.
The dishwasher has detected an abnormal water level
Gorenje identifies F52 as a water-level fault. Clean the coarse and fine filters and inspect the external inlet filter before service.
The dishwasher is overfilling
Gorenje uses F54 for overfilling. Turn off the water tap before unplugging, then arrange service; do not leave the dishwasher filling unattended.
The dishwasher circulation pump has reported a fault
Gorenje identifies F56 as a circulation-pump fault. The official table provides a service boundary, not a user pump replacement procedure.
The dishwasher has detected a water-inlet problem
Gorenje uses F67 for a water-inlet fault. Check the water tap and external inlet-hose filter safely, then use service if the code persists.
spray arm position or drawer-dishwasher condition
A6 is identified by Haier support as spray arm position or drawer-dishwasher condition. Follow the official, model-scoped checks and service boundary below.
drainage issue on a countertop dishwasher
E2 is identified by Haier support as drainage issue on a countertop dishwasher. Follow the official, model-scoped checks and service boundary below.
upper-lid assist alarm on a drawer dishwasher
F5 is identified by Haier support as upper-lid assist alarm on a drawer dishwasher. Follow the official, model-scoped checks and service boundary below.
Anti-flooding overflow protection
F01 is described by Hotpoint support as anti-flooding overflow protection. Exact checks and component access vary by model and region.
The water-fill solenoid valve has failed
Hotpoint identifies dishwasher F02 as a water-fill solenoid-valve failure and recommends booking an engineer.
The dishwasher is not draining correctly
LG uses OE when the dishwasher detects a drain issue. The official checks focus on the filter, drain hose, air gap, and disposal connection.
technical water-inlet fault
F18 is identified by Miele's official manual as technical water-inlet fault. Follow the exact model-scoped checks and safety boundary below.