Dishwasher error codes and fault guides
Browse 235 published, evidence-gated Dishwasher guides. Each page states the supported model and region, official source, safe checks, and the point to stop.
Dishwasher fault guides
97–120 of 235
the drain pump-out exceeded two minutes
C1 is identified by GE Appliances' official support as the drain pump-out exceeded two minutes. Follow the model-scoped checks and service boundary below.
the total pump-out cycle exceeded seven minutes
C2 is identified by GE Appliances' official support as the total pump-out cycle exceeded seven minutes. Follow the model-scoped checks and service boundary below.
the dishwasher will not drain
C3 is identified by GE Appliances' official support as the dishwasher will not drain. Follow the model-scoped checks and service boundary below.
the machine filled twice or its float, drain, or sump is restricted
C4 is identified by GE Appliances' official support as the machine filled twice or its float, drain, or sump is restricted. Follow the model-scoped checks and service boundary below.
the pump-out time was too short
C5 is identified by GE Appliances' official support as the pump-out time was too short. Follow the model-scoped checks and service boundary below.
incoming water temperature is too low
C6 is identified by GE Appliances' official support as incoming water temperature is too low. Follow the model-scoped checks and service boundary below.
the water-temperature sensor circuit is inoperative
C7 is identified by GE Appliances' official support as the water-temperature sensor circuit is inoperative. Follow the model-scoped checks and service boundary below.
the detergent cup is blocked from opening fully
C8 is identified by GE Appliances' official support as the detergent cup is blocked from opening fully. Follow the model-scoped checks and service boundary below.
the detergent cup is not closed
Cup Open is identified by GE Appliances' official support as the detergent cup is not closed. Follow the model-scoped checks and service boundary below.
the dishwasher failed to drain
FTD / F56 is identified by GE Appliances' official support as the dishwasher failed to drain. Follow the model-scoped checks and service boundary below.
a low-water condition was detected
H2O is identified by GE Appliances' official support as a low-water condition was detected. Follow the model-scoped checks and service boundary below.
the dishwasher has a low-water condition
H2O is identified by GE Appliances' official support as the dishwasher has a low-water condition. Follow the model-scoped checks and service boundary below.
the leak-detection system has detected a possible leak
LEAK DETECTED is identified by GE Appliances' official support as the leak-detection system has detected a possible leak. Follow the model-scoped checks and service boundary below.
the dishwasher may have experienced a power surge or control interruption
Other blinking lights is identified by GE Appliances' official support as the dishwasher may have experienced a power surge or control interruption. Follow the model-scoped checks and service boundary below.
power to the dishwasher was interrupted
PF is identified by GE Appliances' official support as power to the dishwasher was interrupted. Follow the model-scoped checks and service boundary below.
the pressure sensor is sending an invalid signal
PrS is identified by GE Appliances' official support as the pressure sensor is sending an invalid signal. Follow the model-scoped checks and service boundary below.
the dishwasher is resetting or has been interrupted
Start or Start/Reset blinking is identified by GE Appliances' official support as the dishwasher is resetting or has been interrupted. Follow the model-scoped checks and service boundary below.
the dishwasher door was unlatched during a cycle
beep every 30 seconds is identified by GE Appliances' official support as the dishwasher door was unlatched during a cycle. Follow the model-scoped checks and service boundary below.
the dishwasher door was unlatched during a cycle
beep every minute is identified by GE Appliances' official support as the dishwasher door was unlatched during a cycle. Follow the model-scoped checks and service boundary below.
The dishwasher has detected too much water
Gorenje identifies F10 as a dishwasher overfilling condition. The official first check is the accessible drainage pump area; use service if F10 persists.
The dishwasher cannot discharge water correctly
Gorenje uses F11 for a water-outlet fault. Check the accessible filters, pump area, and visible drain path with power isolated before service.
The dishwasher is not receiving water correctly
Gorenje identifies F12 as a water-inlet fault. Check the tap and external inlet-hose filter only after closing water and isolating power.
The dishwasher inlet valve is leaking
Gorenje uses F40 for an inlet-valve leakage condition. Close the water tap immediately and arrange service; do not attempt a valve repair.
The dishwasher heater has reported a fault
Gorenje identifies F41 as heater fault 1. Close the water tap, unplug the dishwasher, and use qualified service for the heater diagnosis.