Dishwasher error codes and fault guides
Browse 235 published, evidence-gated Dishwasher guides. Each page states the supported model and region, official source, safe checks, and the point to stop.
Dishwasher fault guides
121–144 of 235
The dishwasher diverter has reported a fault
Gorenje uses F45 for a diverter fault. The official table does not verify a user repair, so record the model and arrange service.
The dishwasher has detected an abnormal water level
Gorenje identifies F52 as a water-level fault. Clean the coarse and fine filters and inspect the external inlet filter before service.
The dishwasher is overfilling
Gorenje uses F54 for overfilling. Turn off the water tap before unplugging, then arrange service; do not leave the dishwasher filling unattended.
The dishwasher circulation pump has reported a fault
Gorenje identifies F56 as a circulation-pump fault. The official table provides a service boundary, not a user pump replacement procedure.
The dishwasher has detected a water-inlet problem
Gorenje uses F67 for a water-inlet fault. Check the water tap and external inlet-hose filter safely, then use service if the code persists.
spray arm position or drawer-dishwasher condition
A6 is identified by Haier support as spray arm position or drawer-dishwasher condition. Follow the official, model-scoped checks and service boundary below.
drainage issue on a countertop dishwasher
E2 is identified by Haier support as drainage issue on a countertop dishwasher. Follow the official, model-scoped checks and service boundary below.
upper-lid assist alarm on a drawer dishwasher
F5 is identified by Haier support as upper-lid assist alarm on a drawer dishwasher. Follow the official, model-scoped checks and service boundary below.
upper-lid assist alarm on a drawer dishwasher
F5X is identified by Haier support as upper-lid assist alarm on a drawer dishwasher. Follow the official, model-scoped checks and service boundary below.
Anti-flooding overflow protection
F01 is described by Hotpoint support as anti-flooding overflow protection. Exact checks and component access vary by model and region.
The water-fill solenoid valve has failed
Hotpoint identifies dishwasher F02 as a water-fill solenoid-valve failure and recommends booking an engineer.
a water-drain failure or timeout
F03 is identified in Hotpoint's official United Kingdom appliance-specific table as a water-drain failure or timeout. Use only the published external check or service boundary below.
a water-fill timeout
F06 is identified in Hotpoint's official United Kingdom appliance-specific table as a water-fill timeout. Use only the published external check or service boundary below.
a damaged water turbine
F07 is identified in Hotpoint's official United Kingdom appliance-specific table as a damaged water turbine. Use only the published external check or service boundary below.
a temperature-timeout fault
F08 is identified in Hotpoint's official United Kingdom appliance-specific table as a temperature-timeout fault. Use only the published external check or service boundary below.
a software error
F09 is identified by Hotpoint's official, appliance-specific source as a software error. Follow only the model-scoped checks and safety boundary below.
a heating-element fault
F10 is identified in Hotpoint's official United Kingdom appliance-specific table as a heating-element fault. Use only the published external check or service boundary below.
a wash-pump failure
F11 is identified by Hotpoint's official, appliance-specific source as a wash-pump failure. Follow only the model-scoped checks and safety boundary below.
a communication error between the main board and display
F12 is identified in Hotpoint's official United Kingdom appliance-specific table as a communication error between the main board and display. Use only the published external check or service boundary below.
a virtual-sensor error
F15 is identified in Hotpoint's official United Kingdom appliance-specific table as a virtual-sensor error. Use only the published external check or service boundary below.
The dishwasher is not draining correctly
LG uses OE when the dishwasher detects a drain issue. The official checks focus on the filter, drain hose, air gap, and disposal connection.
a diverter leak, also displayed as FAE5 on some models
F10E5 is identified by Maytag's official support as a diverter leak, also displayed as FAE5 on some models. Follow the model-scoped checks and safety boundary below.
a dishwasher control-module condition
F1E1 is identified by Maytag's official support as a dishwasher control-module condition. Follow the model-scoped checks and safety boundary below.
a main-control communication error
F1E2 is identified by Maytag's official support as a main-control communication error. Follow the model-scoped checks and safety boundary below.