Gorenje error codes and fault guides
Browse 82 published, evidence-gated Gorenje guides. Each page states the supported model and region, official source, safe checks, and the point to stop.
Gorenje fault guides
1–24 of 82
The dishwasher has detected too much water
Gorenje identifies F10 as a dishwasher overfilling condition. The official first check is the accessible drainage pump area; use service if F10 persists.
The dishwasher cannot discharge water correctly
Gorenje uses F11 for a water-outlet fault. Check the accessible filters, pump area, and visible drain path with power isolated before service.
The dishwasher is not receiving water correctly
Gorenje identifies F12 as a water-inlet fault. Check the tap and external inlet-hose filter only after closing water and isolating power.
The dishwasher inlet valve is leaking
Gorenje uses F40 for an inlet-valve leakage condition. Close the water tap immediately and arrange service; do not attempt a valve repair.
The dishwasher heater has reported a fault
Gorenje identifies F41 as heater fault 1. Close the water tap, unplug the dishwasher, and use qualified service for the heater diagnosis.
The dishwasher diverter has reported a fault
Gorenje uses F45 for a diverter fault. The official table does not verify a user repair, so record the model and arrange service.
The dishwasher has detected an abnormal water level
Gorenje identifies F52 as a water-level fault. Clean the coarse and fine filters and inspect the external inlet filter before service.
The dishwasher is overfilling
Gorenje uses F54 for overfilling. Turn off the water tap before unplugging, then arrange service; do not leave the dishwasher filling unattended.
The dishwasher circulation pump has reported a fault
Gorenje identifies F56 as a circulation-pump fault. The official table provides a service boundary, not a user pump replacement procedure.
The dishwasher has detected a water-inlet problem
Gorenje uses F67 for a water-inlet fault. Check the water tap and external inlet-hose filter safely, then use service if the code persists.
The dryer control unit has reported a failure
Gorenje identifies E00 as a control-unit failure. Record the exact model and use qualified service; no control-board replacement is inferred.
a tumble-dryer temperature-sensor failure
E01 is identified by Gorenje support as a tumble-dryer temperature-sensor failure. Follow the official, model-scoped checks and service boundary below.
The dryer has detected a communication error
Gorenje identifies E02 as a communication error. Capture the exact code and model, then use qualified service for the internal connection diagnosis.
The condensate pump is not pumping water to the tank normally
Gorenje identifies E03 as a condensate-pump error. Check the user-accessible condensate path and stop if the code persists.
tumble-dryer system overheating
E04 is identified by Gorenje support as tumble-dryer system overheating. Follow the official, model-scoped checks and service boundary below.
The dryer control unit has reported a failure
Gorenje groups E07 and E08 as control-unit failures. Disconnect the dryer from power and arrange qualified service.
The BLDC motor and control unit are not communicating
Gorenje identifies E11 as a BLDC motor communication error. Do not open the motor circuit; arrange service with the exact dryer model.
The dryer cannot connect to the Wi-Fi network for remote control
Gorenje identifies E17 as a Wi-Fi network connection issue affecting remote control, not the dryer’s normal drying programmes.
The dryer has detected a temperature-sensor failure
Gorenje groups E91, E92, and E93 as temperature-sensor failures. Stop using the dryer and arrange service rather than guessing a sensor part.
The drying cycle was interrupted by a power failure
Gorenje uses PF for a power-supply failure warning. Resume once with Start/Pause, then investigate the household supply if PF returns.
a refrigerator Wi-Fi-module malfunction
81 is identified by Gorenje support as a refrigerator Wi-Fi-module malfunction. Follow the official, model-scoped checks and service boundary below.
a freezer-compartment door-open or door-sensor condition
C1 is identified by Gorenje support as a freezer-compartment door-open or door-sensor condition. Follow the official, model-scoped checks and service boundary below.
a refrigerator-compartment door-open or door-sensor condition
C2 is identified by Gorenje support as a refrigerator-compartment door-open or door-sensor condition. Follow the official, model-scoped checks and service boundary below.
a combined refrigerator-and-freezer door-open or sensor condition
C3 is identified by Gorenje support as a combined refrigerator-and-freezer door-open or sensor condition. Follow the official, model-scoped checks and service boundary below.